CODAN 5900 High Power VSAT Ku-Band Transceivers

CODAN 5900 series VSAT Ku-Band high power  transceivers offer a wide range of distinctive advantages and enhanced features for satellite communications systems based in remote or challenging geographic regions.

Available in single or dual synthesiser options, Ku-Band frequency bands and 70 or 140MHz IF configurations-and a range of power outputs- CODAN  5900 series VSAT transceivers provide industry leading technical performance.

Key features

Durability

The CODAN 5900 series VSAT transceivers are designed and tested to meet their performance specifications in an ambient temperature range from -40°C to +55°C, ensuring long-term survival in extreme conditions. Field experience shows that MTBFs of greater than 60,000 hours can be expected.

RF performance

RF performance is superb, particularly intermodulation performance, gain stability over temperature and flatness across the IF band.

These transceivers also boast industry leading spurious and harmonics specifications while guaranteed RF performance ensures expensive system link margins do not have to be used to cope with RF transceiver variations. The high linearity and low spurious characteristics contribute to superior multi-carrier performance.

Output power options

The CODAN 5900 series Ku-Band VSAT transceiver is available with 40 watts output rating.

Power consumption

CODAN high power VSAT transceivers low power consumption and low temperature rise, ensuring internal components do not suffer undue stress.

Power supply

All the high power transceivers are AC mains powered and may be field selected to operate from either 115 V AC or 230 V AC.

Internal protection

Internal protection against high temperature and short or open circuit RF output is standard.

Enhanced monitor and control

All operating functions can be controlled and monitored via the serial interface, and the operating configuration is stored in EEPROM to ensure the set-up parameters are restored in the event of a power failure.

Universal interface compatibility

The CODAN 5900 series VSAT transceivers has universal interface compatibility capable of operating with dumb terminals, laptop/PC emulating terminals, handheld terminals and personal organisers without requiring proprietary software. The versatile configuration options support contact closure, RS232, RS422 and RS485 (2 or 4 wire).

Two dedicated controllers are available from Codan:

• CODAN 5560 Hand-Held Controller, suitable for in the field installation setup
• CODAN 5570 Remote Controller, suitable for indoor rack mounting to provide permanent monitoring and control capabilities

Redundancy switching system

A redundancy switching system is available to provide an automatic changeover to a second transceiver to maximise availability and minimise any disruption to service. This system is fully outdoor mounted, but can be supplied with the CODAN 5587 Redundant System Monitor to provide indoor monitoring and control.

Major configuration options

VSAT Ku-Band transmit frequency band (GHz) - Transmit 

VSAT Ku-Band receive frequency bands

All systems use the common CODAN 5900 series VSAT converter module, which has an RF input of 950-1700 MHz. Receive bands are selected by the use of an appropriate LNB. Standard frequency bands are listed below.

VSAT Ku Band LNB (Standard noise temperature 90 K)

(LNBs are phase locked to the internal 10 MHz reference in the 5900 converter module).

Bandwidth

• CODAN Hand-Held Controller
• CODAN Remote Controller
• CODAN Redundancy Switching Systems
• CODAN Transmit Reject Filters
• CODAN Antenna Mounting Kits

CODAN quality and service

The high power transceivers are built and tested in CODAN ISO9001 quality certified manufacturing facility, and undergo 100% burn in and performance monitoring.

CODAN fully trained staff and agents provide in-factory and in-country training services and complete installation and on-site assistance. This service is backed up by a 24 hour customer service line and a warranty of three years on manufacturing, design or component defects.

Technical specifications

Transmit section

IF input

Frequency range Narrow BW option Wide BW option	70 + 20 MHz/140 + 20 MHz selectable 140 + 40 MHz
Impedance	50/75 Ω selectable
Connector	N-type female
Return loss	18 dB minimum at 50 Ω

Gain specification

Gain	78 dB minimum (0 dB SSPA & Converter attenuator settings)
Attenuator ranges	0 to 25 dB nominal (Converter) 0 to 20 dB nominal (SSPA)
Attenuator step size	1 dB nominal
Gain flatness Over IF Narrow BW option Wide BW option Over frequency range	±1.0 dB maximum, 40 MHz ±2.0 dB maximum, 80 MHz ±2.0 dB maximum
Gain stability	+1.5 dB maximum, -40°C to +50°C

RF output

Frequency range	14.0 to 14.5 GHz
Connector	WR75
VSWR	1.25:1 maximum
Output power (1 dB GCP)	+46 dBm (40W) minimum at 25°C
Carrier to intermodulation ratio	-25 dBc, two carriers, each at 6 dB OPBO from 1 dB GCP
Spurious output	-60 dBc maximum at 1 dB GCP
Harmonics	-50 dBc maximum at 1 dB GCP

Low noise block cconverter

Indicative specifications.

Input

Pass band	10.95 to 12.75 GHz
Insertion loss	0.05 dB maximum
Reject band	13.75 to 14.5 GHz
Rejection	55 dB minimum

Noise figure

Noise figure

1.2 dB @ 25°C maximum 1.0 dB typical

Indicators	Online, Alarm, Standby, Maintenance
Display	Output power, Heatsink temperature, Alarms
Controls	State, Gain

Standby, On, Warm-up, SSPA activated, Converter temperature, Converter fault, LNB fault, SSPA fault, Temperature fault, SSPA inhibit control, SSPA activate control, Transmit frequency, Receive frequency, Transmit attenuation, Receive attenuation, Cable compensation, Reference oscillator override, SSPA alarm enable, LNB alarm enable, Temperature compensation select, Packet address (ASCII mode only), Packet address range (ASCII mode only), Packet protocol select (ASCII mode only), SSPA mode select, Converter lock, Status change poll.

Remote control functions (serial interface)

Power control (standby/on), SSPA inhibit control, SSPA activate control, Transmit frequency, Receive frequency, Transmit attenuation, Receive attenuation, Cable compensation, Reference oscillator override, SSPA alarm enable, LNB alarm enable, Temperature compensation select, Address range select (ASCII mode only), Packet protocol select (ASCII mode only), SSPA mode select, Reset, Reset change bits.

Remote monitoring functions (contact closure)

Standby, Warm-up, SSPA activated, Converter fault, LNB fault, SSPA fault, Temperature fault.

Remote control functions (contact closure)

Power control (standby on), SSPA inhibit control, SSPA activate control.

Power 

Input voltage	104 to 274 V AC, 47 to 63 Hz
Power consumption	500 VA typical, SSPA on

SSPA module

All dimensions are measured over the connectors.

Size